I know rachel is attempting her own bicycle lighting project, so I am hoping that by putting notes on the wiki we can share ideas. Rigel
rigel's dynamo lighting system
This will be based around the Shimano DH-3N71 Dynamo hub. It outputs 3W at 6V. I'm not sure how the voltage or current changes as speed increases, but I am under the impression that it is fairly well-regulated internally.
Currently, I have it wired directly to a rectifier, whose output is a 220uF cap and a Cree XR-E LED. This produces light adequate to ride in the dark and avoid most obstacles. None of this is regulated in any way, so at low (slightly faster than walking) speeds it begins to flicker. This might be a problem for long steep climbs in the dark.
What I would like, ideally, is to have the ability to draw current from a li-ion battery pack when it begins to flicker. In addition, I would like to be able to charge the batteries, and additionally a cellphone if feasible, from the dynohub when i am riding in daylight. I have not found the drag to be noticeable from one LED, but presumably if drawing more current this could become a problem.
Since I am a n00b, I dont know the first thing about implementing this, but i have been led (ha!) to believe that i need the following modules:
- voltage regulator
- battery charging circuit
- led driver circuit
- 5V usb output for alternative uses
The cree LEDs are brightest, i'm told, when drawing 600-700mA. The voltage drop, i believe, is 3.3v per LED, and they are best wired in series to avoid thermal runaway (not sure why this happens, but it's been talked about on several forums i've seen, so i think it best to avoid it altogether) I would probably start with 2, but may use as many as 4 li-ion cells for this purpose.
- reflector design - will likely try to use the reprap for this. are there software packages for this sort of thing?
- What voltage regulator should i use?
- for a circuit that's powered by a battery only, no voltage regulator is required, at least not in general. if one uses a battery that provides too much voltage, then some means of dropping the voltage to the load circuit is needed (this can be diodes in series to the load). in the case of a battery and load being refreshed by a charger (e.g. something connected to pedals), then it's probably a good idea to protect from over-voltage (spikes) and to protect from possible reverse currents. - if power drain is a problem and you've determined you should use a voltage regulator, look at specs for switching regulators rather than linear regulators. --Jstockford 11:17, 26 November 2008 (PST)
- do i need a multiple output voltage regulator or should i step up the voltage in the battery charger module itself?
- what battery-charger IC should i use?
- maybe none, possibly just passive components and diodes, maybe an active circuit using transistors or op amps. --Jstockford 11:17, 26 November 2008 (PST)
- what kinds of interconnects (i would like this to be modular for the working design) are waterproof (and cheap!), as i will be using this in potentially foul weather?
- where is this circuit physically (might be no where at the moment, might be bits and pieces on a bike or on a shelf...). --Jstockford 11:21, 26 November 2008 (PST)
Rachel's automated lighting
The point of my system is that I don't have to remember to turn it off (or on). The first rev will be battery powered; a later revision may take advantage of Rigel's work and connect to a dynamo.
Rev one will contain a couple bright white LEDs in front and some red LEDs behind. The front will be steady, the rear blink, as is often seen on bicycles. The base is a seat cover, in which is embedded a pressure switch such that the lights are only on when the seat is occupied (a later rev will change this to leave the lights on for 2 minutes after the seat becomes unoccupied). An additional switch, to prevent unnecessary daylight use, is a photoresistor which will shut off power to the lights if it sees more than X amount of light.
- 1x or 2x 555 timer chips
- 1x LM393 (op amp) analog comparator for voltages
- 1x photoresistor
- 1x pot
- various resistors & capacitors to produce the right 555 outputs
- 1x fabric pressure sensor
- fabric for seat cover
- batteries as needed
I have the 555 circuit modelled for a nice rate of flash for the rear LEDs, using 3V.
The photoresistor registers about 140k ohms in inside natural light, held under the bike seat. In the bathroom with the door mostly shut, simulating nighttime, it registers 22M. Tentative initial ON value: 20Mohm.
Learned a bit of comparator chip circuit theory from David... Have the op amp circuit breadboarded out such that it turns on one LED when the photoresistor is occluded. Circuit includes a pot for calibration, forming the second voltage divider.
Still need transistor circuit as all the LEDs together will be more current than the op amp can handle. That is the last piece of circuit.
Big(?) capacitor behind seat switch s/b sufficient to keep lights on for some time after seat is vacated. How big must it be?
I can create the seat cover with embedded pressure switch whenever, it's just a switch, so it can wait until last.