Difference between revisions of "PCB Etching Tutorial"

From Noisebridge
Jump to: navigation, search
(Steps)
Line 22: Line 22:
  
  
- Single sided copper PCB board
+
* Single sided copper clad board -- [[ https://www.google.com/search?q=copper+clad+fr4&ie=utf-8&oe=utf-8]]
- Traces (should already have been designed on some CAD program)
+
* Circuit board trace layout in a printable format (pdf or postscript ps works, design this with an [[EDA program]])
- Glossy Printer Paper (to print the traces on)
+
* Glossy Inkjet Photo Paper (to print the traces on)
- Iron  
+
* Iron or press
-Ferric Chloride Solution (to dissolve the copper from the board)
+
* Etchant chemical
- WetorDry paper
+
*# Ferric Chloride Solution (to dissolve the copper from the board)
- Container to put PCB in with chemical solution
+
*# Muriatic Acid
 +
* WetorDry paper
 +
* Container to put PCB in with chemical solution
  
  
 
== '''Steps''' ==
 
== '''Steps''' ==
 +
 +
''If you are using Ferric Chloride(FeCl3) foretchant, then start heating your etchant to 50C''
  
  
Line 38: Line 42:
 
Make sure to clean any junk from the copper board before beginning the process!
 
Make sure to clean any junk from the copper board before beginning the process!
  
  - Use WetorDry paper / fine sand paper to clean the PCB under water until it turns pink
+
* Use WetorDry paper / fine sand paper to clean the PCB under water until it turns pink
  - Wipe off water with a clean towel
+
* Wipe off water with a clean towel
  - Use acetone to remove oils from PCB  
+
* Use acetone to remove oils from PCB  
  
 
[ insert Cleaning pics here]
 
[ insert Cleaning pics here]
 
  
  
Line 49: Line 52:
 
'''2) Printing the Traces:'''
 
'''2) Printing the Traces:'''
  
Grab your printer and print the traces onto the glossy printer paper  
+
Grab your Laser printer and print the traces onto the glossy inkjet photo paper.
    - be sure traces are nice and thick
+
* we used walgreens 8.5x11 stock inkjet photo paper with fine results
    -  check the preferences for a "no scaling"
+
* We used the Noisebridge Brother HL-5470DW and generic Laser printer toner with fine results
    - Design must be mirrored
+
* Make sure your print driver isn't scaling or distorting the circuit layout
    - Only use black ink
+
* Use monochrome and highest resolution possible for your printer
    - Print at the highest resolution possible
 
  
 +
The printer operator should also take this opportunity to provide feedback to the circuit designer:
 +
* Make sure the design traces are thick enough for this process (XXmil/XXmm minimum trace width with 20mil/0.508mm minimum clearance)
 +
* Make sure the export file is mirrored. The Laser Printer toner is going to 'transfer' to the surface of the copper clad and become unmmirrored in the process
 +
   
 
[insert printing pics here]
 
[insert printing pics here]
  

Revision as of 18:32, 8 September 2016

DIY PCB Etching : Using Chemicals

Chances are you've probably seen a PCB before and it might of looked a little something like this

[Insert a picture of an example of a PCB maybe a Raspberry Pi or an Arduino etc]

The most important part of a PCB is the traces which connect the components to each other. These traces made in a CAD program for PCBs like : Eagle CAD , KiCAD etc

[Insert Picture of traces here]

This tutorial will show you how to make a simple single sided PCB using a chemical method. In summary the traces will be transferred and covered in a solid copper board , then the parts of copper not needed will stay expoxed. Finally the parts not needed will be removed with chemicals.

[Insert picture of before and after here ]


Materials Needed

  • Single sided copper clad board -- [[ https://www.google.com/search?q=copper+clad+fr4&ie=utf-8&oe=utf-8]]
  • Circuit board trace layout in a printable format (pdf or postscript ps works, design this with an EDA program)
  • Glossy Inkjet Photo Paper (to print the traces on)
  • Iron or press
  • Etchant chemical
    1. Ferric Chloride Solution (to dissolve the copper from the board)
    2. Muriatic Acid
  • WetorDry paper
  • Container to put PCB in with chemical solution


Steps

If you are using Ferric Chloride(FeCl3) foretchant, then start heating your etchant to 50C


1) Preparing the Copper Board: Clean It

Make sure to clean any junk from the copper board before beginning the process!

  • Use WetorDry paper / fine sand paper to clean the PCB under water until it turns pink
  • Wipe off water with a clean towel
  • Use acetone to remove oils from PCB

[ insert Cleaning pics here]


2) Printing the Traces:

Grab your Laser printer and print the traces onto the glossy inkjet photo paper.

  • we used walgreens 8.5x11 stock inkjet photo paper with fine results
  • We used the Noisebridge Brother HL-5470DW and generic Laser printer toner with fine results
  • Make sure your print driver isn't scaling or distorting the circuit layout
  • Use monochrome and highest resolution possible for your printer

The printer operator should also take this opportunity to provide feedback to the circuit designer:

  • Make sure the design traces are thick enough for this process (XXmil/XXmm minimum trace width with 20mil/0.508mm minimum clearance)
  • Make sure the export file is mirrored. The Laser Printer toner is going to 'transfer' to the surface of the copper clad and become unmmirrored in the process

[insert printing pics here]


3) Transferring the Traces to the PCB:

  - Press down the glossy paper with the design onto the copper PCB 
  - Use a hot iron to press down glossy paper to the PCB [INSERT PIC HERE OF IRON PRESSED]
  - After the glossy paper stick onto the PCB submerge the two in a tray of water and gently press down the paper so it peels off leaving the trace on the PCB 
 [insert PCB iron down pic here]



4) Get Rid of the remaining Copper

  - Place the Ferric Chloride Solution Bottle  inside tray of hot water (this will heat the solution and make the PCB copper to be dissolved faster) 
  - Pour some of the solution into a tray along with your PCB 
  - Check the PCB every 5 or so minutes to check if the copper has been fully removed
[insert PCB blood water pics here]