Pulse Necklace

From Noisebridge
Jump to navigation Jump to search

A choker (tight necklace) which measures your heartbeat (pulse) and shows it to others via a set of LEDs. It may also optionally communicate the same info to the wearer via a vibrator. Although theoretically heart rate should be known via senses intrinsic to humans, in practice it is actually quite difficult to know, and I think there are many interesting social interactions that pulse-display could trigger.

Currently Eric Boyd and Chung-Hay are working on this device.

Design Thoughts

Sensor:

Generally all commercial ones a just little electrocardiogram units.

From http://en.wikipedia.org/wiki/Electrocardiography :

"An electrocardiogram is obtained by measuring electrical potential between various points of the body using a biomedical instrumentation amplifier. A lead records the electrical signals of the heart from a particular combination of recording electrodes which are placed at specific points on the patient's body."

However, for this project I think the best solution may be optical. There is apparently a small change in the optical properties of your skin with your blood pressure, meaning that pulse can be observed by an optical sensor pressed against your skin. I have a working "pulse watch" which uses this principle.


Display: Initially, only to people other than the wearer, via a string of LEDs inside the choker. I imagine the pulsing centered on the LED in the center, and going out to all, then coming back in, similar to how some star trek (?) lights worked when the computer talked. There may also be a lone vibrator, which could be used to signal to the wearer a variety of things (like pulse, but also time or low battery etc). Although this is really stretching the definition of "display", the device might also log data for later retrieval via USB.

Armature: Choker, plus it is likely that it will have to have a pendant hanging from it, which would contain the circuit and battery. The vibrator might also be in the pendant. The hard part of the armature will be how to wire the LEDs in a "soft" way (no ribbon cables around our necks!). Also, the optical sensor will have to be held against the neck even while the neck moves, you breathe, etc - that might be tricky. We have experimented with conductive thread with crimp beads, but they are very difficult to use, and end up being more fragile than is really acceptable. We are presently investigating silk-screening conductive paint, and flexible PCBs are possible armature ideas.

Electronics: For prototype, arduino and probably a small op-amp circuit modeled on the circuit inside the watch. To make it wearable, we'll probably have to use an attiny or other similarly super small device.


Prior Art

I already have a set of chokers with surface mount LEDs inside (I've shown this at prior meetings during show and tell). I am unsure of how the LEDs are wired - it's possible that they are all controlled from the same wire, in which case the device will not be able to display as above, and instead will simply flash. I got the chokers from Rebeccas for only $2.15 each, so if they are suitable they make great kit components.

Reverse engineering the choker's flexible PCB:

Lights: 1-12, counted from the batteries
  (Only lights 1, 3, 5, 6, 7, 8, 10, 12 are populated)
Pins: 1-6, counted from the big ground of the batteries nearest the ribbon cable

Schematic Reverse Engineer:
Pin 1: V+ for all lights
Pin 2: V- for 1, 3, 5
Pin 3: V- for 2, 4
Pin 4: V- for 6, 8
Pin 5: V- for 7, 9, 11
Pin 6: V- for 10, 12

Apparently the LEDs are very easy to fry, since both green and pink choker now have many non-functional LEDs


I've done some google searches, but I haven't been able to find anything like this. There are some pulse-sensing watches, for instance Chinavasion: Exercise Watch - pulse + calorie reader or see some reviews at Heart Rate Monitors. These devices almost universally have a small display, but I think a haptic solution could be greatly superior.

PulseWatch.jpg

You can see in the image a small heart on the left side of the display. When it's sensing your pulse, this heart blinks with your pulse, which is super cool. The sensor is under my index finger on the right hand side. You need to just touch the sensor - if you press hard, that destroys the signals (presumably because the pressure makes it so your skin doesn't respond to the pressure of your blood and instead just responds to the pressure of your hold...)

Hack Notes

June 24th, 2009

July 1st, 2009

July 8st, 2009

July 15th, 2009

Circuit Research, July 21st, 2009

July 22th, 2009

Custom Stencil Design Research, July 28th, 2009

July 29th, 2009

August 2nd, 2009

August 5th, 2009

August 12th, 2009

August 16th, 2009

Sept 16th, 2009

Sept 29th, 2009

Oct 1st, 2009

Oct 2nd, 2009

Oct 8th, 2009

Oct 11th, 2009

Oct 15th, 2009

Nov 8th, 2009

Nov 12th, 2009

Nov 15th, 2009

Lessons Learned Along the Way

Lessons on Conductive Paint

Lessons on Paint Thinning