Difference between revisions of "User talk:Jarrod"

From Noisebridge
Jump to: navigation, search
(Wiring: new section)
m (Water heater)
 
(2 intermediate revisions by the same user not shown)
Line 12: Line 12:
  
 
I remain available to assist with this or other Noisebridge projects.  [[User:Frank|Frank]] ([[User talk:Frank|talk]]) 09:58, 21 February 2017 (UTC)
 
I remain available to assist with this or other Noisebridge projects.  [[User:Frank|Frank]] ([[User talk:Frank|talk]]) 09:58, 21 February 2017 (UTC)
 +
 +
==Water heater==
 +
Jarrod, I brought in a 14AWG cord-set for the water heater yesterday.  I left it in the box with the other parts under the sink.  I removed most of the teflon tape on the heater pipe threads, because the fittings being used have built in gaskets, and pipe thread tape should not be used.  I also cleaned up most of the mess around the sink.  I found a half full can of red paint without a lid on the sink.  I put it in a bucket on the floor.
 +
 +
The water heater is a very old model, (Powerstar 45-552704), and I do not know if it still works.  The manuals are not available for this model.
 +
 +
I checked the water heater in rest room.  It seems to be the same model.  I measured the voltage, which was 113 V.  It seems to supply reasonably warm water at this lower than nameplate voltage. 
 +
 +
I couldn't solve a couple of problems.  The cold water valve on the wall does not turn off completely, and I was afraid to start work, without being able to turn off the water.  These under-sink valves always seem to leak.  We may have to shut off the water further upstream.  I would replace this with a ball valve.
 +
 +
Another problem is that the faucet should be replaced.  The cold water handle is missing and the stem is stripped.  We will need a tee so that both hot and cold water can be supplied.
 +
 +
I can get parts and install them, but I don't feel comfortable working without a way to shut the water off.
 +
 +
Let me know what you think.    [[User:Frank|Frank]] ([[User talk:Frank|talk]]) 19:12, 28 February 2017 (UTC)

Latest revision as of 06:44, 1 March 2017

Wiring[edit]

Jarrod, thanks for your hospitality Saturday.

I have a disclosure to make. I did not connect a protective ground wire to the two outlets I installed, because I did not find a protective ground coming from the panel board. The devices will be grounded as long as the conduit stays intact. Unfortunately, fittings tend to come loose over time.

I thought the conductors I used might have been too big, and the conduits and boxes might have been too small. Looking at the NEC today confirms my suspicions. I created a page of data from the NEC. As you can see, a 1/2" EMT conduit has room for only one 6 AWG THHN conductor. A 4" junction box does not have room for any 6 AWG conductors at all.

I like the larger than required conductors, because they stay cool, but they also need larger conduits and boxes.

I also found out today that wire nuts go up to 8 AWG maximum.

I remain available to assist with this or other Noisebridge projects. Frank (talk) 09:58, 21 February 2017 (UTC)

Water heater[edit]

Jarrod, I brought in a 14AWG cord-set for the water heater yesterday. I left it in the box with the other parts under the sink. I removed most of the teflon tape on the heater pipe threads, because the fittings being used have built in gaskets, and pipe thread tape should not be used. I also cleaned up most of the mess around the sink. I found a half full can of red paint without a lid on the sink. I put it in a bucket on the floor.

The water heater is a very old model, (Powerstar 45-552704), and I do not know if it still works. The manuals are not available for this model.

I checked the water heater in rest room. It seems to be the same model. I measured the voltage, which was 113 V. It seems to supply reasonably warm water at this lower than nameplate voltage.

I couldn't solve a couple of problems. The cold water valve on the wall does not turn off completely, and I was afraid to start work, without being able to turn off the water. These under-sink valves always seem to leak. We may have to shut off the water further upstream. I would replace this with a ball valve.

Another problem is that the faucet should be replaced. The cold water handle is missing and the stem is stripped. We will need a tee so that both hot and cold water can be supplied.

I can get parts and install them, but I don't feel comfortable working without a way to shut the water off.

Let me know what you think. Frank (talk) 19:12, 28 February 2017 (UTC)